Nearly everybody maintains their own individual idea with regards to A Step-by-Step Guide to Installing a Bathtub.
Mounting a tub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently accessible, the task can move easily; if you need to open a wall surface to eliminate the old bathtub and place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as embeded in the new one. Make certain you have certified on your own for the work as well as are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is far better to think about utilizing one before you start. Opportunities are you might need an expert plumber to make tube links.
This post will certainly assist you set up a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to change the setup of your previous water pipelines.
Your tools and also material checklist must make up the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be fairly bothersome because of the restricted accessibility that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Making use of both wooden boards under its feet, put the tub in the required placement. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by examining the level and changing the feet on the bath tub till the level reviews level.
To mount taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water supply and check all joints and new pipework for leakages and also tighten them if essential. Load the bathtub as well as likewise examine the overflow outlet and the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait up until the tub has actually been utilized a minimum of when as this will certainly settle it into its final position.
Preparing for the Setup
First of all, the sustaining framework provided with the bath needs to be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the faucet features a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a comment further down. We'd be pleased to find out your views about this review. In hopes to see you back again later on. Are you aware of somebody else who is enthusiastic about the topic? Please feel free to promote it. Thanks a lot for your time spent reading it.
Visit Url